All Products
This ashtray pod is a direct replacement for the factory ashtray in your Mitsubishi Lancer Evolution 7, 8, and 9 (CT9A), purpose-built to mount a Haltech 8-button CAN keypad. Remove the original ashtray, slide this one in, and you've got a clean, OEM-looking home for your keypad — no drilling, no cutting, no modified trim.
It puts your Haltech 8-button CAN keypad right at your fingertips for cockpit control of your ECU and electronics, positioned at a clean angle in the center console. The updated design now includes a tab on the back for an extra-firm hold, so the pod stays locked in place. Printed in ASA for high UV and heat resistance, it won't warp or fade in a hot cabin. Designed and 3D printed in-house in Los Angeles.
Install is straightforward: pop out the original ashtray, route your keypad wiring, and slide the pod into place. Easy wiring, easy install — and fully reversible if you ever want the ashtray back.
Details
Fits vehicle: Mitsubishi Lancer Evolution 7, 8, 9 (CT9A, 2001–2007)
Holds: Haltech 8-button CAN keypad
Mounts in: the factory ashtray opening — no drilling or cutting
Hold: now includes a rear tab for an extra-firm fit
Material: ASA — high UV and heat resistance; won't warp or crack
Install: tool-free pod fitment, easy wiring, fully reversible
Mount your Haltech keypad where it belongs — clean, OEM-style, and right where you can reach it. Slide the ashtray out and drop it in
This center console gauge pod adds a clean, OEM-style home for your 52mm gauges in the Mitsubishi Lancer Evolution X (CZ4A). It's a direct-fit addition to the Evo X center console — slide your gauges in, mount the pod, and you've got factory-looking gauge placement without cutting or modifying your interior.
Made for 52mm gauges, it installs cleanly: slide the gauges into the pod, set it into the center console, secure it with the supplied retainers, and route your wiring through the square opening in the back. Printed in ASA with high UV and heat resistance, it won't warp, fade, or crack in a hot cabin. Designed and 3D printed in-house in Los Angeles.
Details
Fits vehicle: Mitsubishi Lancer Evolution X (CZ4A, 2008–2016)
Mounts in: the center console — direct fit, no cutting or modification
Gauge size: 52mm only
Material: ASA — high UV and heat resistance; won't warp or crack
Install: supplied retainers; wiring routes through the rear square opening
Get clean, OEM-style 52mm gauge placement in your Evo X — slide them in, secure the pod, and wire it up.
This gas cap holder gives your fuel cap a proper place to sit instead of hanging and scratching your paint, on the Mitsubishi Lancer Evolution 7, 8, and 9 (CT9A). It's a 3D-printed ASA holder that sits right on your fuel door with an OEM-like look and fit — and unlike stick-on holders, it mounts with a built-in bracket and needs no double-sided tape at all.
This is the new and improved model: stronger, longer-lasting, and with a cleaner engraved font. Printed in ASA for heat and UV durability, it can be custom engraved with almost any text or design, so you can make it your own while keeping that factory-clean look. Tuned to sit flush in the fuel door, it won't wiggle loose, break, or interfere with your OEM gas cap. Designed and 3D printed in-house in Los Angeles.
Installation is tool-free and takes seconds: slide the top into the overarching bracket, press on the bottom edge, and slide it down — no tape required. One important note: this is a 3D-printed piece, not metal, so handle it gently. Ease the top up, guide the holder toward the gas door, then slide it down — forcing it or installing it incorrectly can crack it. Give it a little care on install and it'll last.
Details
Fits: Mitsubishi Lancer Evolution 7, 8, 9 (CT9A, 2001–2007)
Fixes: a gas cap that hangs loose and scratches your paint
Mounts: built-in bracket, sits on the fuel door — no double-sided tape, no drilling
Custom: engrave almost any text or design
Material: ASA — stronger, longer-lasting, heat- and UV-resistant
Fit: OEM-like; won't wiggle loose or affect the OEM gas cap
Install: tool-free; handle gently — 3D-printed plastic, not metal
Give your gas cap a clean, OEM-style home — and put your own name or design on it. Clip it in, no tape, no drilling.
This gas cap holder stops you from laying your fuel cap on your paint and scratching it on the Nissan Silvia S15. It's a 3D-printed holder that sits right on your fuel door with a clean, OEM-like fit — it won't wiggle loose, break, or interfere with your OEM gas cap, giving the cap a proper place to rest every time you fuel up.
Install takes seconds with no tools: peel back the double-sided tape, align it to the center of your fuel door, and press it on. Tape is included. Designed and 3D printed in-house in Los Angeles.
Details
Fits: Nissan Silvia S15 (1999–2002)
Fixes: a gas cap laid on your paint and scratching it
Fit: OEM-like; won't wiggle loose or affect the OEM gas cap
Install: tool-free adhesive mount, seconds; double-sided tape included
Give your gas cap a clean place to sit and keep your paint scratch-free — peel, stick, done.
This ashtray gauge pod mounts your gauges in the factory ashtray opening of the Mitsubishi Lancer Evolution 7, 8, and 9 (CT9A) — no drilling, no cutting, and no damage to your A-pillar. Instead of permanently modifying a clean, good-condition A-pillar, you slide out the stock ashtray and drop this 3D-printed ASA pod straight into its place.
It's printed in ASA, so it won't warp, shrink, or crack in a hot cabin the way cheaper materials do — it holds its shape and your gauges stay put for the long haul. Install takes under 30 seconds and is fully reversible: slide the ashtray out, push the pod in, done. Want your interior back to stock for resale? Pull the pod and slide the ashtray back in. Available in single (one gauge) and double (two gauge) versions. Designed and 3D printed in-house in Los Angeles.
Details
Fits: Mitsubishi Lancer Evolution 7, 8, 9 (CT9A, 2001–2007)
Mounts in: the factory ashtray opening — no A-pillar drilling or cutting
Options: single (1 gauge) or double (2 gauge)
Gauge size: [FILL: fits 52mm / 60mm gauges — specify]
Material: ASA — won't warp, shrink, or crack; heat- and UV-resistant
Install: tool-free, under 30 seconds, fully reversible
Keep your A-pillar factory-clean and still get your gauges exactly where you want them — slide the ashtray out and you're set.
Made for the Link 4-button CAN keypad, this ashtray pod is a direct replacement for the factory ashtray in your Mitsubishi Lancer Evolution 7, 8, and 9 (CT9A). It's a clean, compact way to mount a 4-button keypad when you only need a handful of functions at your fingertips — remove the original ashtray, slide the pod in, and you're set. No drilling, no cutting, no permanent changes.
The pod is sized specifically for the Link 4-button keypad and positions its backlit, customizable buttons at a clean angle in the center console — ideal for the essentials like launch, boost, traction, or a fuel pump without a full button array taking over your interior. The latest version adds a tab on the back for an extra-firm hold. Printed in ASA with high UV and heat resistance, it won't warp or fade in a sun-baked cabin. Designed and 3D printed in-house in Los Angeles.
Installation is quick: pull the factory ashtray, route your keypad wiring, and slide the pod into place. Easy wiring, easy install — and fully reversible if you ever want the ashtray back.
Details
Fits vehicle: Mitsubishi Lancer Evolution 7, 8, 9 (CT9A, 2001–2007)
Holds: Link 4-button CAN keypad (sized to the 65×70mm unit)
Mounts in: the factory ashtray opening — no drilling or cutting
Hold: rear tab for an extra-firm fit
Material: ASA — high UV and heat resistance; won't warp or crack
Install: tool-free pod fitment, easy wiring, fully reversible
Keep it clean with just the controls you need — slide the ashtray out, drop the pod in, and your Link 4-button keypad's ready to wire up.
Built to hold the Link 8-button CAN keypad, this pod is a direct replacement for the factory ashtray in your Mitsubishi Lancer Evolution 7, 8, and 9 (CT9A). Pull the original ashtray, slide the pod in, and your keypad sits in a clean, OEM-looking spot in the center console — no drilling, no trimming, no permanent changes.
Your Link CAN keypad's backlit, customizable buttons end up right at your fingertips for cockpit control of launch, boost, traction, fuel pump, and whatever else you've mapped. The latest version adds a tab on the back for an extra-firm hold so the pod won't budge. It's printed in ASA with high UV and heat resistance, so it won't warp or fade where the sun hits the console. Designed and 3D printed in-house in Los Angeles.
Installation is quick and clean: remove the factory ashtray, route your keypad wiring, and slide the pod home. Easy wiring, easy install — and fully reversible whenever you want the ashtray back.
Details
Fits vehicle: Mitsubishi Lancer Evolution 7, 8, 9 (CT9A, 2001–2007)
Holds: Link 8-button CAN keypad
Mounts in: the factory ashtray opening — no drilling or cutting
Hold: rear tab for an extra-firm fit
Material: ASA — high UV and heat resistance; won't warp or crack
Install: tool-free pod fitment, easy wiring, fully reversible
Give your Link keypad a factory-clean home right where you can reach it — ashtray out, pod in, done
Link CAN Keypad buttons are exactly what's missing when your keypad arrives blank. These are 3D-printed replacement button inserts for the Link CAN Keypad, made in translucent PETG so the keypad's per-button LED backlight shines cleanly through each one and every function stays easy to read, day or night. They drop straight into the keypad's interchangeable insert format with no modification — the part you actually need to read and use the keypad you already bought.
We print in translucent PETG on purpose: it lets the keypad's RGB backlighting transfer through the face of each button so you can identify every control at a glance, even in a dark cockpit, while staying tough enough for daily driving and track use. Installation takes under 30 seconds — work the inserts in one by one as shown in the manual, plug the keypad in, and you're on the road testing it. Designed and 3D printed in-house in Los Angeles.
Details
Fits: Link CAN Keypad — drops into the standard interchangeable 15mm insert slots
Material: translucent PETG — durable and backlight-friendly
Backlight: transfers the keypad's per-button LED light for clear day and night legibility
Install: tool-free, under 30 seconds, plug-and-play
In the set: [FILL: how many inserts + which legends/icons]
[FILL if applicable: color or finish options]
Got your Link CAN Keypad and need buttons that actually light up and last? Add these to your build and you're sorted.
This armrest latch fixes the loose, non-locking center console armrest on the Mitsubishi Lancer Evolution 7, 8, and 9 (CT9A). It's a 3D-printed replacement clip in high-quality ASA, built for an OEM+ fit that snaps your armrest shut with a secure, tight hold again — no more lid that won't stay latched.
We print it in ASA because it's heat- and UV-resistant and stays strong in a hot cabin, so it won't go brittle or warp the way worn factory plastic does — exactly what you want from a part that latches every time you use the armrest. Installation is straightforward: it reuses your original M3 screws and drops into the factory location with no trimming and no hiccups. Designed and 3D printed in-house in Los Angeles.
Details
Fits: Mitsubishi Lancer Evolution 7, 8, 9 (CT9A, 2001–2007)
Fixes: a loose or non-locking armrest that won't stay shut
Material: high-quality ASA — heat- and UV-resistant, durable
Fit: OEM+ for a secure, tight latch
Install: reuses your original M3 screws, no modification
Includes: 2 per pack
Tired of an armrest that pops open every time you lean on it? Grab a pack and get that solid factory latch back
This gauge pod turns the blank HID/foglight switch panel in your Mitsubishi Lancer Evolution 7, 8, and 9 (CT9A) into a clean home for a 52mm gauge. If your Evo didn't come with HIDs or foglights, that panel is just empty space — this 3D-printed ASA pod drops straight into it, no drilling and no wasted real estate.
It fits 52mm gauges and installs in under 30 seconds with no tools: pop out the stock blank panel, push the pod into place, and lock it in with the 4 provided clips. Printed in ASA, it won't warp, shrink, or crack over time, so your gauge stays put even in a hot cabin. Designed and 3D printed in-house in Los Angeles.
Details
Fits vehicle: Mitsubishi Lancer Evolution 7, 8, 9 (CT9A, 2001–2007)
Mounts in: the blank HID/foglight switch panel location (Evos without factory HIDs/foglights)
Gauge size: 52mm only
Material: ASA — won't warp, shrink, or crack; heat- and UV-resistant
Install: tool-free, under 30 seconds; locks in with 4 included clips
Got an empty HID/foglight panel? Put a 52mm gauge there instead — pop the panel out, clip the pod in, and you're done.
This gas cap holder stops your fuel cap from hanging and scratching your paint every time you fill up. It's a 3D-printed ASA holder with an OEM+ fit that mounts to your fuel door and gives the cap a secure spot to sit, instead of dangling against your bodywork. The new and improved design fits every Mitsubishi DSM and 4–6 generation Lancer Evolution.
Printed in ASA, it won't crack, warp, or break down over time the way brittle plastics do — it shrugs off the heat and sun where it sits on the fuel door. Install takes under 30 seconds with no tools: peel the strip(s) off the pre-applied double-sided tape, line it up, and press it onto your gas door. Tape is included. Designed and 3D printed in-house in Los Angeles.
Confirmed fitment runs across the DSM lineup — Mitsubishi Eclipse, Eagle Talon, and Plymouth Laser — plus the Mitsubishi 3000GT and Lancer Evolution 4, 5, and 6 (CN9A/CP9A). One important note: this does not fit the Evo 7–9.
Details
Fits: Mitsubishi DSM (Eclipse, Eagle Talon, Plymouth Laser), Mitsubishi 3000GT, and Lancer Evolution 4–6 (CN9A/CP9A, 1996–2001)
Does NOT fit: Lancer Evolution 7–9 (CT9A)
Fixes: a gas cap that hangs loose and scratches your paint while fueling
Material: ASA — won't crack, warp, or break; heat- and UV-resistant
Fit: OEM+, new and improved design
Install: tool-free adhesive mount, under 30 seconds; double-sided tape included
Stop letting your gas cap chip away at your paint. Peel, stick, done — and never think about it again.
hese double-DIN stereo brackets let you install a double-DIN head unit in your Mitsubishi Lancer Evolution 7, 8, and 9 (CT9A) without drilling — no holes in your new head unit and no cutting the factory support brackets. They're 3D-printed in ASA and crafted to sit perfectly within the dash trim at the proper angle, so your stereo ends up flush and straight.
Because they mount to your head unit's side screw holes — the part standardized across the ISO 7736 double-DIN size — most aftermarket double-DIN units bolt straight in (very deep or oversized units may vary). Printed in ASA, they won't warp, sag, or break down over time, holding your stereo securely for the long haul. Designed and 3D printed in-house in Los Angeles.
Installation is straightforward: reuse the 4 screws on the side of the stereo, attach the brackets, push the unit into the dash, screw it in, and you're done.
Details
Fits vehicle: Mitsubishi Lancer Evolution 7, 8, 9 (CT9A, 2001–2007)
Fits stereo: standard double-DIN head units (ISO 7736), mounted via the 4 side screws
Benefit: no drilling your head unit or cutting the factory support brackets
Material: ASA — won't warp, sag, or crack; heat- and UV-resistant
Install: reuses the stereo's 4 side screws; sits at the correct trim angle
Upgrade to a double-DIN without butchering your dash or your new stereo — bolt the brackets on and drop it in.
This gas cap holder stops you from leaving your fuel cap on your paint and scratching it on your Nissan GT-R. It's a 3D-printed ASA holder that gives the cap a secure place to sit right on your fuel door, so every fill-up stays scratch-free.
Printed in ASA, it won't warp, shrink, or break down over time, even with heat and sun on the fuel door. Install takes seconds with no tools: peel back the provided double-sided tape, line it up, and press it on. Tape is included. Designed and 3D printed in-house in Los Angeles.
Details
Fixes: a gas cap left on your paint, scratching it
Material: ASA — won't warp or shrink; heat- and UV-resistant
Install: tool-free adhesive mount, seconds; double-sided tape included
Keep your GT-R's paint scratch-free at every fill-up — peel, stick, done.